Q3 2026 CBAM Price Rises to €82.32: Checks for EU Stainless Steel Imports

The quarterly certificate price rose about 9.4 percent from Q2. For buyers importing stainless steel into the EU, the next steps are to confirm covered CN codes, review annual import volumes and arrange the emissions evidence needed for the declaration covering 2026 imports.

Industry & standards updatesPublished

The European Commission published the Q3 2026 CBAM certificate price on 5 October at €82.32, up €7.04 from the Q2 price of €75.28. This price applies to certificates for covered goods imported into the EU from July through September 2026.

European Commission headquarters in the Berlaymont building in Brussels
Berlaymont building in Brussels, headquarters of the European Commission. Photo: Romaine / Wikimedia Commons (CC0 1.0); cropped for this page.

One certificate corresponds to one tonne of carbon dioxide equivalent emissions. €82.32 is therefore a carbon price, not a charge per tonne of stainless steel. The financial effect on an order also depends on its embedded emissions and the applicable adjustments, including EU ETS free allocation and any eligible carbon price already paid.

The Q3 figure should not be treated as the confirmed price for goods imported into the EU in Q4 2026. The Commission currently lists 4 January 2027 as the Q4 publication date; its price table does not yet show a Q4 value.

When comparing quotations, keep the material price separate from any estimated CBAM liability. Check which emissions figures the estimate uses and what supporting records the producer can provide. Then confirm the CN code for the goods you intend to import.

Stainless steel product headings to check

CBAM scope follows the CN code, the EU customs classification for the goods. Common headings for stainless steel are listed below. Confirm the full eight-digit code for the actual item with the EU importer or customs representative against the current CBAM Annex I.

Scroll horizontally to see every column.

Product Common CN heading Classification detail
Plate, sheet, coil and strip 7219 or 7220 Flat-rolled stainless steel 600 mm wide or more falls under 7219; less than 600 mm under 7220.
Bars, rods and sections 7221 or 7222 7221 covers hot-rolled rod in irregularly wound coils; other stainless bars, rods and sections fall under 7222.
Seamless pipe and tube 7304 Confirm material, dimensions and the applicable subheading.
Welded circular pipe over 406.4 mm outside diameter 7305 Circular cross-section and outside diameter above 406.4 mm are key conditions.
Other welded pipe, tube and hollow sections 7306 Confirm cross-section, construction and dimensions; distinguish from 7305.
Flanges and pipe fittings 7307 The fitting type determines the subheading.
Forgings and custom parts Item-specific Possible headings include 7218, 7222, 7307 or 7326. Some finished machinery parts may fall outside current CBAM scope.

For forgings, distinguish semi-finished stock from finished components before assigning a CN code. A component’s function and degree of processing can affect its classification; the grade alone does not determine whether it is covered. The Commission’s iron and steel guidance explains the sector’s covered goods and production processes.

Review the annual threshold and declaration dates

The current mass-based threshold is 50 tonnes of net mass per importer per calendar year, aggregated across covered iron and steel, aluminium, cement and fertiliser goods. If that total is exceeded, the relevant CBAM obligations apply to all covered imports during the year, including earlier shipments. Electricity and hydrogen are excluded from this threshold exemption.

Certificates for 2026 imports become available for purchase from February 2027. The first annual declaration and corresponding certificate surrender are due by 30 September 2027. Keep customs entry records and net weights available for reconciliation with the declaration.

Plan the emissions evidence before ordering

Under the verification rules, importers can use Commission default values or actual verified emissions, subject to the applicable requirements. For actual values, the non-EU production installation calculates the emissions and an accredited CBAM verifier checks the calculation and supporting evidence. The authorised declarant uses the verified data for its declaration.

A material test certificate helps identify the material and its heat or lot. Actual emissions require separate installation-level data and accredited verification. If you intend to use actual values, establish whether the relevant producer can supply the required evidence before committing to the order.

The Commission’s timeline provides for the first verification reports to be issued from January 2027. During 2026, buyers can ask about installation identification, monitoring arrangements and verification plans without expecting a completed annual report at the quotation stage.

Prepare the records for each covered shipment

Before purchase, agree on the information needed for the specific goods:

  • the confirmed eight-digit CN code, origin and expected net mass;
  • the production installation and planned emissions reporting method;
  • the material and heat or lot references linking the goods to their records; and
  • who supplies each required document, in which format and by what date.

If an order combines stock from different sources, keep each batch linked to its records. A single commercial invoice does not establish that all goods came from one production installation.

Questions about quotations and mixed imports

  • Which quarter applies if the order was placed before July?

    For 2026, the applicable quarterly certificate price follows the quarter of import into the EU. An earlier order date or a later certificate purchase does not change the quarter to which those imports belong.

  • Does the price rise increase the steel quotation by 9.4 percent?

    No. That percentage compares Q3 and Q2 certificate prices. It does not describe a change in the steel price or total landed cost. Compare quotations using the same scope and assumptions for any separately stated CBAM estimate.

  • Can smaller steel orders exceed the threshold when combined with aluminium?

    Yes. For example, an importer bringing in 40 tonnes of covered steel and 15 tonnes of covered aluminium in the same year reaches 55 tonnes. This illustrative total exceeds the threshold even though neither sector alone exceeds 50 tonnes.

  • What should a quotation say if verified emissions data are still pending?

    If a CBAM estimate is included, state whether it uses Commission default values or assumes verified actual emissions. List the missing evidence, who will provide it and when the estimate will be updated.

Confirm the material and documents for your order

For a 310S, 309S, 253MA or other heat-resistant stainless steel enquiry, send us the product form, dimensions, quantity, destination and document requirements. We can check the mill certificates, heat or lot references, inspection records and packing information available for the offer. List any CBAM emissions evidence separately so we can check its availability before you order.

Discuss your material and document requirements

Official sources

Send your RFQ

Required fields are marked with an asterisk.

Up to 5 files · 10 MB each · 50 MB total. PDF, Office, images, DWG, DXF, STEP/STP and IGES/IGS.

    0 files · 0 MB

    By submitting, you agree that Hechuang Stainless Steel may use these details to respond to your request. Privacy notice.